Just How to Install a Bathtub Yourself
Just How to Install a Bathtub Yourself
Blog Article
Are you trying to locate advise around How to Install a Bathtub Yourself?
Installing a bath tub isn't precisely rocket science, but it does call for strong plumbing, woodworking, as well as sometimes, tiling abilities. Changing an old bathtub with a brand-new one is likewise a moderately tough job. If the old bathtub is easily accessible, the job can move immediately; if you have to open up a wall to get rid of the old bathtub as well as position the brand-new tub, the job is much harder. In either case, the task is within a house handyman's skills, although you will certainly need an assistant to move out the old bathtub and embeded in the new one. See to it you have certified yourself for the work and fit attempting it. Rather than employing a specialist to take control of a halfway-completed task, it is far better to consider employing one before you begin. Possibilities are you might require a specialist plumber to make tube connections.
This article will assist you set up a brand-new tub in your washroom if you have actually currently bought a new tub and do not need to alter the setup of your previous supply of water pipelines.
Your devices and product list should make up the following:
Preparing for the Setup
Firstly, the sustaining frame provided with the bath must be fitted (if needed) according to the producer's instructions. Next off, fit the faucets or mixer to the tub. When fitting the faucet block, it is necessary to ensure that if the tap features a plastic washer, it is fitted between the bath as well as the taps. On a plastic bath, it is likewise practical to fit a sustaining plate under the faucets system to avoid stress on the bath tub.
Fit the versatile faucet connectors to the bottom of the two faucets making use of 2 nuts and olives (in some cases provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and after that pass the electrical outlet through the hole in the bathroom. Make use of the nut supplied by the supplier to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the flexible overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which must be fitted inside the bath. Make sure you utilize every one of the provided washers.
Attach the trap to the bottom of the waste electrical outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Attach all-time low of the overflow tube in a similar manner.The bath need to currently prepare to be suited its last setting.
Removing Old Taps
If you need to replace old taps with brand-new ones as a part of your installment, after that the first thing you must do is detach the water system. After doing so, activate the faucets to drain pipes any kind of water continuing to be in the system. The procedure of getting rid of the existing faucets can be fairly troublesome because of the restricted access that is often the case.
Utilize a basin wrench (crowsfoot spanner) or a faucet device to reverse the nut that attaches the supply pipelines to the faucets. Have a cloth ready for the remaining water that will certainly come from the pipes. As soon as the supply pipelines have been eliminated, utilize the very same tool to loosen the nut that holds the taps onto the bath/basin. You will certainly need to stop the solitary taps from turning throughout this process. When the faucets have been eliminated, the holes in the bath/basin will certainly have to be cleaned up of any kind of old sealing compound.
Prior to going on to fit the new faucets, contrast the pipe connections on the old faucets to the brand-new taps. If the old taps are longer than the brand-new faucets, then a shank adapter is required for the brand-new faucets to fit.
Installing the Tub
Utilizing both wood boards under its feet, place the tub in the called for position. The wood boards are helpful in uniformly spreading out the weight of the tub over the location of the boards instead of focusing all the weight onto 4 small points.
The following goal is to make sure that the bath tub is leveled all round. This can be achieved by inspecting the level and changing the feet on the tub till the spirit level reads degree.
To mount taps, fit the bottom of the outermost adaptable tap port to the ideal supply pipe by making a compression join; then do the very same for the various other tap.
Turn on the water system and also check all joints and brand-new pipework for leakages and also tighten them if necessary. Fill up the tub as well as additionally check the overflow outlet as well as the typical electrical outlet for leakages.
Ultimately, fix the bath paneling as explained in the maker's user's manual. Tiling and also securing around the bathtub should wait until the tub has been utilized at the very least when as this will certainly resolve it right into its last placement.
Suitable New Touches
If the tails of the new taps are plastic, then you will need a plastic connector to avoid damages to the string. One end of the port fits on the plastic tail of the faucet and also the various other end supplies a link to the current supply pipelines.
If you require to fit a monobloc, after that you will certainly need minimizing couplers, which connects the 10mm pipe of the monobloc to the basic 15mm supply pipe.
Next, position the tap in the mounting opening in the bath/basin making certain that the washing machines remain in location between the tap and the sink. Secure the faucet in position with the supplier supplied backnut. When the tap is securely in place, the supply pipelines can be attached to the tails of the taps. The taps can either be connected by utilizing corrugated copper piping or with regular faucet ports. The former kind needs to be linked to the tap ends first, tightening up just by hand. The supply pipes can later be attached to the various other end. Tighten both ends with a spanner after both ends have actually been attached.
Tiling Around the Tub
In the area where the bathroom fulfills the ceramic tile, it is necessary to secure the joins with a silicone rubber caulking. This is important as the installation can move enough to fracture a stiff seal, causing the water to pass through the wall surface between the bathroom as well as the tiling, resulting in complications with wetness as well as possible leakages to the ceiling below.
You can pick from a range of coloured sealants to assimilate your fixtures and also fittings. They are marketed in tubes as well as cartridges, and can sealing voids up to a size of 3mm (1/8 inch). If you have a larger void to fill up, you can fill it with spins of soaked paper or soft rope. Remember to constantly load the bathtub with water prior to securing, to allow for the motion experienced when the bathtub is in usage. The sealer can crack relatively very early if you do not consider this motion prior to sealing.
Additionally, ceramic coving or quadrant ceramic tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are likewise conveniently available on the market. It is a good idea to fit the floor tiles using water-resistant or water resistant glue and also grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Do you enjoy reading about Tools You Need to Install a New Bathtub ? Post feedback directly below. We will be pleased to listen to your ideas about this entry. We are looking forward that you come back again before long. Are you aware of another person who is curious about How to Install a Bathtub? Be sure share it. Thanks a lot for your time. Kindly come visit our website back soon.
Get Quote
Report this page